I diagnosed and repaired an HVAC cooling issue on a Trane 2-ton system. The problem was a frozen evaporator coil due to low refrigerant. I located the leak, repaired the line, and recharged the system with R-22 refrigerant. Cooling was restored, and the system is now operating efficiently.

I installed a new American Standard 2-ton Platinum 18 SEER HVAC system. The job included mounting the outdoor condenser unit, connecting the copper lineset, and setting up the new indoor air handler. After the installation, I tested for leaks and ensured proper refrigerant charge.

I repaired a zoned AC system for a homeowner using a Honeywell zoning system. The issue was a malfunctioning zone control board. I replaced the board, checked the wiring for each zone, and recalibrated the thermostats. Both zones are now cooling as expected.

I sealed leaks in the home’s ductwork using Aeroseal to improve energy efficiency. The home had significant duct leakage causing poor cooling in certain rooms. After sealing the ducts, I performed an airflow test to confirm improved performance, and the home is now cooling evenly.

I repaired a Goodman GSX14 air conditioner that was blowing warm air. Upon inspection, I found the capacitor was faulty and needed replacement. I installed a new Titan PRO 440V capacitor and tested the refrigerant levels. After completing the repairs, the AC was cooling efficiently, and all components were operating within the manufacturer’s specifications.

I upgraded a customer’s thermostat to a Nest Learning Thermostat. I removed the old thermostat, connected the new unit’s wiring to the existing HVAC system, and configured the settings for optimal performance. After testing, the thermostat was fully operational, allowing the customer to control their home’s temperature remotely via the Nest app.

I installed an Aprilaire 5000 whole-home air purifier. I mounted the unit to the HVAC system’s return duct, connected the wiring, and calibrated the system to work alongside the existing furnace. After installation, I tested the purifier to ensure it effectively removed dust, allergens, and other airborne particles, significantly improving the home’s indoor air quality.

I conducted maintenance on a Lennox XP16 heat pump. I started by cleaning the outdoor condenser coils to ensure proper heat exchange. I checked refrigerant levels and inspected the electrical connections for signs of wear. After verifying the defrost cycle and testing the unit in both heating and cooling modes, the heat pump was operating at peak efficiency.

Wrapping up a maintenance on a Trane XL20i heat pump system. I cleaned the outdoor coil using Nu-Calgon Evap Pow'r-C, checked refrigerant charge, and calibrated the Trane ComfortLink II thermostat. I replaced the air filter with a MERV 11 pleated filter and cleaned the condensate drain line using a CO2 blaster. System efficiency was restored to peak levels.

Out in Cary this morning working for a longtime client. I installed an American Standard Gold 17 2-stage heat pump (4A7V7060A1000A) with a matching air handler (TAM9A0C60V51DA). I mounted the outdoor unit on a composite pad and connected the lineset using brazing alloy and nitrogen purge. I wired the system, including the new AccuLink Platinum 1050 thermostat, and charged it with R-410A to manufacturer specifications.

I repaired a Carrier Infinity 24ANB1 heat pump experiencing frequent short cycling. Diagnosis revealed a faulty thermistor on the outdoor coil. I replaced the thermistor and verified proper resistance values. I also cleaned the condenser coil and checked refrigerant charge. After repair, I monitored the system through several cycles to ensure proper operation.

In Cary, NC this morning. I installed an American Standard Platinum 95 gas furnace (AUD2C100A9V5VB) in a residential application. I connected the PVC flue and intake pipes, ensuring proper slope and support. I wired the furnace to the electrical supply and thermostat, and connected the gas line using appropriate fittings. After installation, I performed a combustion analysis and adjusted for optimal efficiency.

I addressed poor indoor air quality in an office building by installing a Global Plasma Solutions GPS-iMOD modular ionization system. I mounted the ionization bars in the air handling units and connected them to the GPS-iDETECT auto-cleaning system. After installation, I used an ion meter to verify ion output and distribution throughout the ductwork.

Performed an AC replacement in Cary today. I installed a new American Standard Gold 17 air conditioner. Removed the old unit and replaced it with the new system, including an American Standard S9V2 furnace. Connected the refrigerant lines and set up the condensate drain. Charged the system with R-410A refrigerant and tested for proper operation. The homeowner now enjoys a reliable and energy-efficient cooling system.

Today, I installed a new AC system in a residential home. The existing unit was outdated and inefficient, so I replaced it with an American Standard Silver Series 3-ton air conditioner. After disconnecting the old system, I installed the new outdoor unit, connected the refrigerant lines, and wired the electrical components. Once charged with R-410A refrigerant, I tested the system to ensure optimal cooling performance.

Today, I installed a new, customer purchased HVAC system for cooling in a residential property. The old system was beyond repair, so I replaced it with a Trane XR15 4-ton unit. I installed the outdoor condenser, indoor evaporator coil, and connected the ductwork. After ensuring all electrical connections were secure, I charged the system with R-410A refrigerant and conducted a thorough test to confirm efficient cooling performance.

I responded to a service call for an HVAC system that wasn’t cooling properly. After inspecting the system, I found a refrigerant leak in the evaporator coil. I evacuated the remaining refrigerant, repaired the leak using a sealant, and recharged the system with the correct amount of R-410A. After completing the repair, I tested the system to ensure it was cooling efficiently and maintaining proper temperatures.

I completed an AC repair for a unit that was not cooling effectively. Upon inspection, I found a faulty capacitor in the outdoor condenser unit. Using a multimeter, I confirmed the failure and replaced the old capacitor with a new Titan HD 45/5 MFD capacitor. After installation, I tested the system, and the AC resumed normal cooling operation, providing efficient airflow throughout the home.

Air conditioning repair at a residential home. The unit had stopped cooling the home effectively, due to a clogged evaporator coil. The coil was cleaned and a worn-out air filter was replaced, restoring the system's efficiency. After the repair, the air conditioner resumed providing consistent, cool air.

We resolved an uneven cooling issue in a home by balancing the HVAC system. We inspected the ductwork and found airflow restrictions due to dirty ducts and improperly adjusted dampers. After cleaning the ducts, we adjusted the dampers to ensure even air distribution throughout the home. The HVAC unit, a Lennox XC21, was then tested to confirm consistent cooling in all areas. Proper system balancing is crucial for optimal comfort and efficiency.

We addressed a broken thermostat issue by replacing the faulty unit with a new Honeywell T6 Pro model. The old thermostat was malfunctioning, causing irregular temperature control. After installation, we calibrated the new thermostat and tested the system to ensure accurate temperature regulation and proper operation. Trust our team for reliable thermostat replacements and efficient HVAC system performance.

Installed RGF REME HALO-LED in-duct air purification system on Rheem RHLL-HM3617JA air handler. Mounted unit in supply plenum using provided bracket and self-tapping screws. Wired to 24V transformer with 18/2 thermostat cable. Sealed connections with UV-resistant silicone. Configured for optimal UV-C light output and ionization. Tested operation with UVA/UVC light meter. System now actively reduces airborne contaminants, enhancing overall indoor air quality throughout the home.

Investigated temperature control issue in Trane XR16 heat pump system. Performed load calculation using Manual J software, revealing undersized unit for space. Checked refrigerant charge with Fieldpiece SMAN460 digital manifold, finding slight undercharge. Added R-410A to manufacturer specifications. Cleaned condenser and evaporator coils with Nu-Calgon 4291-08 Evap Foam. Replaced clogged air filter with MERV 11 pleated filter. Calibrated Honeywell T10 Pro smart thermostat. Inspected ductwork using FLIR E6-XT thermal camera, identifying significant leakage. Sealed accessible ducts with Hardcast 321 premium tape. System now maintains temperature more effectively, though full resolution may require unit upgrade.

An AC unit was vibrating excessively while running, indicating an issue that needed prompt attention. Upon inspection, we discovered an unbalanced fan blade and loose mounting hardware. To resolve this, we balanced the fan blade, tightened all mounting screws, and installed new rubber isolation pads to minimize vibration. The unit, a Carrier Infinity 24ANB6, was tested post-repair to ensure smooth and quiet operation. Proper maintenance and timely repairs can prevent excessive vibrations and extend the lifespan of your AC system.

In Apex, we installed an Aprilaire 1850 dehumidifier for a whole-home moisture control solution. This high-capacity unit was integrated into the existing HVAC system, connecting to the return air duct. We ensured proper drainage and set up the unit with a dedicated 120V electrical circuit for reliable operation. The installation included configuring the built-in digital humidistat for optimal performance. This setup effectively reduces humidity levels, improving indoor air quality and comfort throughout the home. Trust our expertise for professional dehumidifier installations.