Holly Springs NC Heating & Air Conditioning Service

I completed an AC repair on a 3-ton Rheem unit. The issue was a faulty capacitor causing intermittent cooling. I replaced the capacitor with a new 45/5 MFD 370V unit, cleaned the condenser coils, and tested the system. The AC is now functioning properly, providing cool air.

I performed an AC installation today, upgrading the home to an American Standard 4-ton Platinum 18 SEER unit. This included installing a new evaporator coil, condenser, and programmable thermostat. I also checked refrigerant levels and ran the system to ensure peak performance.

I repaired an HVAC system for cooling in a home with a Lennox 2-ton unit. The issue was a clogged evaporator coil, which was preventing efficient cooling. I cleaned the coil, replaced the air filter with a MERV 8 filter, and checked the refrigerant charge. The system is back to cooling efficiently.

I installed a Reme Halo UV light air purifier into a home’s HVAC system. I mounted the unit inside the supply duct, ensuring it would treat the air as it passed through. The UV light helps neutralize bacteria, mold, and viruses, improving indoor air quality. After testing the system, it was functioning correctly, providing cleaner air throughout the home.

I sealed several leaky ducts in a home using Aeroseal technology. After pressurizing the duct system, I applied the aerosol sealant, which closed off leaks from the inside. This process significantly improved the system’s efficiency by preventing conditioned air from escaping, leading to better airflow and reduced energy costs for the homeowner.

I performed routine maintenance on a Carrier Infinity 24 air conditioner. I inspected and cleaned the condenser coils, checked the refrigerant levels, and replaced the air filter. I also tightened electrical connections and tested the thermostat for accurate temperature control. After testing, the unit was running efficiently, providing proper cooling for the home.

I performed air duct cleaning on a residential HVAC system using a Rotobrush aiR+ machine. I cleaned all supply and return ducts, removing accumulated dust and debris. I used HEPA filtration during the process and applied an EPA-registered antimicrobial treatment. I also sealed several duct leaks using mastic sealant, improving overall system efficiency.

I performed a thorough clean-out of a Rheem RGGE gas furnace. I cleaned the heat exchanger using a soft brush and vacuum, inspected the flue for obstructions, and cleaned the blower wheel. I replaced the flame sensor and checked the igniter gap. I also conducted a static pressure test to ensure proper airflow through the system.

Completed a ductwork repair in a home. Discovered significant air leaks in the main supply duct. Sealed the leaks using UL 181-rated mastic and reinforced the connections with new duct clamps. Inspected the entire duct system and adjusted the airflow dampers to balance the system. The repairs improved the HVAC system’s efficiency, ensuring even heating and cooling throughout the home.

Performed HVAC repair in Holly Springs on a Lennox Elite Series XC14 system. The system had low refrigerant levels and a malfunctioning pressure switch. Replaced the pressure switch and recharged the system with R-410A refrigerant. Checked the blower motor and capacitor to ensure proper airflow and operation. The system is now cooling effectively and maintaining the desired temperature.

In Holly Springs this afternoon. Repaired an air conditioner for our client who had been without AC for a couple of hours. Diagnosed the Goodman GSX14 unit with a failed capacitor. Replaced the capacitor and checked the contact points in the condenser unit. Also inspected the evaporator coil for any blockages. After making the necessary repairs, tested the system to ensure it was cooling properly. The air conditioner is now running smoothly and efficiently.

Repaired ductwork for a client in Holly Springs. Found a significant leak in the flex duct near the main trunk line. Repaired the tear using mastic sealant and reinforced it with new duct insulation. Checked for additional leaks along the duct system and ensured proper airflow throughout the home. The HVAC system is now delivering even temperatures across all rooms.

Performed HVAC repair on a Trane XR14 heat pump. Diagnosed the system and found a faulty contactor. Replaced the contactor with a new OEM part and checked the capacitor to ensure it was functioning correctly. Tested the system’s refrigerant levels and thermostat calibration. After repairs, the unit is now running efficiently and providing consistent heating and cooling.

I completed the installation of a new cooling HVAC system in a residential home, replacing the failed unit with an American Standard Silver Series 4-ton air conditioner. After carefully removing the old equipment, I installed the new outdoor condenser along with a matching evaporator coil. I ensured all connections were properly made, including refrigerant lines and electrical components. Finally, I charged the system with R-410A refrigerant and performed a comprehensive test to verify efficient cooling performance throughout the home.

I performed a zoned AC system upgrade for a home with varying cooling needs. I installed Arzel Zoning Dampers in the existing ductwork, connected them to an Arzel Evergreen Control Panel, and added separate thermostats for each zone. After configuring the system, I tested it to ensure that each zone could be independently controlled, improving overall comfort and energy efficiency throughout the home.

I responded to an HVAC service call for a cooling system that was underperforming. Upon inspection, I found a significant refrigerant leak in the condenser coil. I evacuated the remaining refrigerant, repaired the leak with a high-pressure brazing technique, and recharged the system with R-410A refrigerant. After completing the repair, I tested the system to ensure it was operating efficiently and providing consistent cooling.

Air conditioning service. Discovered that the air conditioning unit's performance issues were due to a dirty filter, which was restricting airflow. After replacing the clogged filter, we thoroughly cleaned the unit and ensured it was running efficiently.

We addressed a frozen refrigerant line on an AC unit. The issue was caused by restricted airflow due to a clogged air filter and low refrigerant levels. We replaced the dirty filter with a new 16x25x1 pleated filter and recharged the system with R-410A refrigerant. After defrosting the line, we tested the unit to ensure it was cooling properly. Regular maintenance prevents such issues and ensures efficient operation.

Diagnosed AC compressor failure on Lennox XC14 outdoor unit. Used Fluke 87V multimeter to test capacitor, revealing low microfarad reading. Replaced 45/5 MFD dual run capacitor with TITAN PRO TOCF45. Checked contactor for pitting, finding excessive wear. Installed new Honeywell DP2030A5004 contactor. Tested compressor windings, confirming proper resistance. Inspected and tightened all electrical connections. Cleaned condenser coils with Nu-Calgon 4291-08 Evap Foam. Verified proper refrigerant charge using Fieldpiece SMAN360 digital manifold. System restarted successfully with 17°F delta T across evaporator coil. Completed repair in 2 hours, restoring optimal cooling performance.

We recently installed an Aprilaire 1850 dehumidifier for whole-home moisture control. This high-capacity unit was integrated into the existing HVAC system to effectively reduce humidity levels. We connected the dehumidifier to the return air duct and set it up with a dedicated 120V electrical circuit for reliable operation. The installation also included configuring the built-in digital humidistat for optimal performance. This setup ensures a more comfortable and healthier indoor environment by preventing excess moisture and mold growth. Trust our expertise for professional dehumidifier installations.

Executed installation of American Standard Platinum 20 SEER 4A7V6036A1000A variable-speed air conditioning system. Positioned condenser on vibration-absorbing isolation pads. Installed matching TAM9A0C48V41DA air handler with AccuClean whole-home air filtration. Ran 7/8" and 3/8" ACR copper lines, insulated with Armaflex. Pressure tested system to 400 PSI with nitrogen. Pulled vacuum to 250 microns using Navac NRP8Di vacuum pump. Charged with R-410A to factory specifications. Configured American Standard AccuLink Platinum 1050 communicating thermostat. Performed comprehensive startup checks, including superheat and subcooling measurements. System now delivering superior comfort and efficiency.

Completed installation of an American Standard Gold 17 SEER 4A7A6036H1000A air conditioning system. Mounted condenser unit on polyethylene pad, ensuring proper leveling. Installed matching air handler 4TXCB049BC3HCAA in attic space. Connected units with 3/8" and 3/4" copper line set, brazed using oxy-acetylene torch. Evacuated system to 500 microns using Yellow Jacket 93600 vacuum pump. Charged with R-410A refrigerant using Fieldpiece SMAN460 digital manifold. Wired to new Honeywell T10 Pro smart thermostat. Performed startup checks, achieving 18°F delta T across evaporator. System now operating at peak efficiency, providing optimal cooling performance.

Repaired condensate line on a Carrier 24ABC6 central air conditioning unit. Located blockage using RIDGID micro CA-350 inspection camera. Cleared obstruction with Milwaukee M12 Airsnake drain cleaning air gun. Flushed line with diluted vinegar solution to eliminate algae buildup. Installed Rectorseal Novent 86661 condensate drain line cleanout to facilitate future maintenance. Applied BioFresh Tab-Treat condensate pan tablets to prevent future blockages. Checked float switch operation with Klein Tools ET310 electrical tester. Verified proper drainage and system operation. Completed repair in 1.5 hours, restoring optimal condensate removal and preventing potential water damage.

Serviced Lennox PureAir S whole-home air purification system. Diagnosed faulty UV lamp and clogged carbon filter. Replaced 36-watt UVC bulb, restoring germicidal capabilities. Installed new MERV 16 filter media and activated carbon insert to enhance particulate and VOC removal. Cleaned photocatalytic oxidation panel to maintain optimal air-cleaning efficiency. Verified proper airflow across system using manometer. Checked electrical connections and calibrated air quality sensor. Final testing confirmed 99.9% reduction in airborne contaminants and appropriate integration with HVAC system. Advised homeowner on quarterly filter maintenance schedule.

Installed a whole-home air purification system to enhance indoor air quality. Evaluated the existing HVAC setup and selected a compatible air purifier. Installed the purifier within the ductwork near the HVAC unit to ensure maximum efficiency. Connected the system to the electrical supply and integrated it with the HVAC controls. Verified the air purifier's functionality, ensuring it effectively removed pollutants, allergens, and contaminants from the air. Conducted a final check to confirm the improved air quality throughout the home.